The welt part of a welt pocket is the narrow strip of fabric that forms the decorative and functional upper and lower lip of the opening for the pocket. Welt pockets can have a single or a double welt lip. These directions will be for a double welt. As with many construction techniques, there are many different ways to do most jobs. This is just one way that seems to works well.
Though there will be a pocket bag inside, the finished double welt pocket looks very much like a large bound buttonhole.
1. Mark pocket position on right side of fabric with your choice of marking method - tailor's chalk, tracing carbon or machine basting would work.
2. Cut the welt strips 1" (2.5 cm) wide for a finished 1/4" (6 mm) wide welt and at least 2" (5.1 cm) longer than the desired pocket opening.
3. Fold welt in half, raw/cut edges together. Place the welt on the right side of the garment. Place the fold of the welt toward the outside and the cut edge is on marked pocket position.
4. Stitch down the middle of each welt. Backstitch at both ends. Lines of stitching must be perfectly straight and parallel. If they're not, this won't turn out properly - start again!
5. Cut the pocket opening. Cut down the middle stopping ½” – ¾” (1.3-1.9 cm) before end of pocket. Clip diagonally to backstitched points. Keep diagonal triangle longer, it’s easier to work with.
6. Turn welts toward inside, carefully press. The welts should just fill the opening with the folded edge of the welts just touching one another.
7. Inside pocket bag - cut the pocket bag the width of the welt plus double the depth you want the pocket to be.
8. On the inside, begin by stitching the (upper) edge of the pocket bag to the cut/raw edge of the top welt. With right sides together, begin on the welt extension, then as you stitch, you'll also sew through the fashion fabric on exactly the previous stitching. Be careful not to catch the triangle in this stitching.
9. a) Fold so that the lower welt is positioned to expose the cut edge of the welt and the bag is "down".
9. b) Then fold the remaining edge pocket bag up to meet the cut edge of the welt thereby covering up the pocket opening hole. Flip over so that you can see where to stitch, then sew beginning on the welt extension through the fashion fabric toward the other end.
10. Fold the fashion fabric back to expose the welt extension and the triangular wedge tab. Stitch across the triangle flush to the body of the garment, stitching through the welt extensions and pocket bag.
11. Trim pocket bag width as desired. Then sew sides of pocket bag together including welt extensions.
If you've never sewn a double welt pocket, I highly recommend creating a sample from fabric that is lightweight, yet has a relatively crisp 'hand' so that when you press the fold in the welts and when you turn the welts to the inside they will press nice and flat.
Pockets: Double Welt Pocket
4 Free Getting-Started Gifts with Subscription
- Instructions for this 'Pretty in Peach Princess Jacket' design
- Instructions for the Color-Blocked T-Shirt
- 4-pg. essential Guide to Sewing Notions
- Drawing tool - Designer's Companion (with 1st order)
You will receive an email asking your to confirm your subscription. (Watch for this in your email Inbox. If it's not there, check your Junk/Spam folder). Then you'll be directed to the Subscription Gifts page where you can choose 1 or more of the Welcome Gifts (see revolving carousel below).
No Spam - Total Privacy - Unsubscribe at any time
To see what the Designer's Companion is used for and how it is different from the Designing Stylus, please click here. PO Box 5698, Eugene, OR 97405 USA (541)344-0422 firstname.lastname@example.org Copyright © 2010-2015, Ranita Corporation, Eugene, OR
**Note** You are currently in the SFD Learning Center. All links below will take you back to the main Sure-Fit Designs website and will open up in a new browsing window.